Spearfishing
Spearguns / Components
$us 5,04
$us 5,60
Ermes Sub Stopper 130
Adjustable both in width and height, it is fixed in the wood by means of integrated anchoring nails. Stopper 130: thickness 1.5 mm, center distance to the anchor 130 mm.
$us 5,04 $us 5,60
$us 13,69
Salvimar Line Retainer
Reduced size line slider in glass loaded nylon. The seat of the line is incorporated inside to favor heavy load tractions.
$us 13,69
$us 5,74 $us 7,18
$us 5,84
$us 7,30
Seac Closed Head
Closed type for inserting parallel elastic bands. Suitable for rods with an external diameter of 28 mm (internal 26 mm).
$us 5,84 $us 7,30
$us 5,84 $us 7,30
$us 6,33 $us 7,91
$us 7,67
$us 8,52
Ermes Sub Hook Crocolock Mono
Aligns the elastic under the barrel and prevents it from coming out after the shot, easy introduction of the line, comes with 2 screws
$us 7,67 $us 8,52
$us 7,67
$us 8,52
Ermes Sub Hook Pretensioning Eagle Mono
Consisting of three parts, a base, a central body where you can hook the line and a lid with a special adjustable spout that prevents the accidental release of the line, the distance is calculated to keep the elastic bands perfectly aligned on a roller. Width 26 mm.
$us 7,67 $us 8,52
$us 7,67
$us 8,52
Ermes Sub Elsa 2 Holes 120
Pre-bent to L at 120 degrees, thanks to the numerous holes it also acts as a reel seat
$us 7,67 $us 8,52
$us 7,67 $us 8,52
$us 7,67 $us 8,52
$us 8,21
$us 9,13
Ermes Sub Elsa 2 Holes L-folded
L-folded, thanks to the numerous holes it also acts as a reel seat
$us 8,21 $us 9,13
$us 5,88
$us 9,73
Ermes Sub Ballast Compartment Cover Kit
Lid for the ballast compartment, indispensable for balancing your weapon, has a convenient wire pass, which can be cut if necessary, leads not supplied, measures of interest 18 mm x 90 mm, complete with inserts and screws M4 x 25 mm.
$us 5,88 $us 9,73
$us 10,95 $us 12,17
$us 10,95
$us 12,17
Ermes Sub Stopper Artiglio 60
Non-linear profile designed to cushion the whiplash of the ogive end stroke to the maximum. Equipped with numerous lightenings, it has two front nails that can be used as a line stop. Supplied with 2.9 x 13 self-tapping screws Artiglio 60: thickness 2 mm, length between centers 60 mm
$us 10,95 $us 12,17
$us 10,95
$us 12,17
Ermes Sub Hook Croco Double
Aligns two pairs of rubber bands under the barrel and prevents it from coming out after the shot, easy introduction of the line, comes with 4 screws
$us 10,95 $us 12,17
$us 12,17 $us 40,16
$us 13,14 $us 14,60
$us 16,43
$us 18,25
Ermes Sub Block Hard/1
Pair of blocks for inverter and gearbox systems, openable, lightweight, the pulley is in Derlin, the parts are laser cut, coupled by threaded pressure inserts.
$us 16,43 $us 18,25
$us 17,52
$us 19,47
Ermes Sub Call Fish Ermes
For all ermes mechanisms and for wooden spearguns in general.
$us 17,52 $us 19,47
$us 18,01
$us 22,51
Seac X-fire 2 Holes Head
Open type with accommodation for two circular elastics, without upper bridge and line fixing system for blocking the rod. Suitable for barrels with an external diameter of 28 mm (internal 26 mm).
$us 18,01 $us 22,51
$us 18,50 $us 23,12
$us 18,50
$us 23,12
Seac X-fire Mono Elastic Head
Open type with housing for a circular elastic, without upper bridge and line fixing system for blocking the rod. Suitable for barrels with an external diameter of 28 mm (internal 26 mm).
$us 18,50 $us 23,12
$us 18,50
$us 23,12
Seac Warhead Guun 28
Quick-loading open type with accommodation for two circular elastics and line fixing system for blocking the rod. Removable stainless steel headband. Suitable for barrels with an external diameter of 28 mm (internal 26 mm).
$us 18,50 $us 23,12
$us 20,44 $us 25,55
$us 20,44
$us 25,55
Omer Complete Head For Cayman Carbon
Omer Complete cylinder head for Cayman Carbon
$us 20,44 $us 25,55
$us 20,44
$us 25,55
Seac Double Head 28mm
Hybrid type that allows to pass easily from the double elastic version to the one with circular elastic bands. Suitable for barrels with an external diameter of 28 mm (internal 26 mm).
$us 20,44 $us 25,55
$us 54,76
$us 60,84
Ermes Sub Block Hard/3
Pair of blocks for inverter and gearbox systems, openable, lightweight, the pulley is in Derlin, the parts are laser cut, coupled by threaded pressure inserts.
$us 54,76 $us 60,84
$us 21,90
$us 24,34
Ermes Sub Stopper Tube 110
Cut from a tube with external diameter 16 mm and internal 13 mm, equipped with numerous lightenings, clean design, it avoids cutting the thread against the stopper, the measures have been optimized to the best, simulating all the construction needs. stopper tube 16x1,5x170 weight gr. 31
$us 21,90 $us 24,34
$us 23,00 $us 25,55
$us 24,09
$us 26,77
Ermes Sub Call Fish Siren
This useful tool has been designed to be applied on the whole series of Ermes mechanisms, the wheel can be positioned to the right or left, it can also be operated by holding it comfortably in the hand and attached to the wrist. The firing pin beats against the gear emitting a click with variable intensity controlled by the operator, various species are attracted by the characteristic ticking and it is in the imagination of the fisherman to adapt to the situations that arise. For all ermes mec
$us 24,09 $us 26,77
$us 63,89
$us 26,28
$us 29,20
Ermes Sub Stopper Tube 170
Cut from a tube with external diameter 16 mm and internal 13 mm, equipped with numerous lightenings, clean design, it avoids cutting the thread against the stopper, the measures have been optimized to the best, simulating all the construction needs. Stopper tube 16x1,5x170 weight gr. 31
$us 26,28 $us 29,20
$us 60,23
$us 66,93
Ermes Sub Block Hard/5
Single block with two Derlin pulleys, allows you to attach up to 5 elastic bands for geared inverter systems, openable, light, the pulleys are in derlin without bearings, we opt for this solution as the micro bearings currently on the market do not allow exaggerated loads.
$us 60,23 $us 66,93
$us 38,33
$us 42,59
Ermes Sub Block Hard/7
Single block with two Derlin pulleys, allows you to attach up to 7 elastic bands for geared inverter systems, openable, light, the pulleys are in derlin without bearings, we opt for this solution as the micro bearings currently on the market do not allow exaggerated loads.
$us 38,33 $us 42,59
$us 112,56
$us 118,64
Salvimar Vacuum Head Kit
Testata per sistema sottovuoto in alluminio alleggerita, composta da ogiva, guarnizione di tenuta, corpo e boccola di ammortizzo ad alta resistenza. Disponibile in diverse misure.
$us 118,64
$us 49,28
$us 54,76
Ermes Sub Head Formula Invert
Turned from solid in floating plastic, the stopper is in shockproof material, created expressly for cable systems, supplied with 2 o rings that can be moved at will in the 3 special seats, in two models, with high speed steel bearings (mod Iron) and with pulleys with highly smooth Sliding core (Mod. Sliding). Screw and washers M4 x 60 included.
$us 49,28 $us 54,76
$us 52,45
$us 65,59
Sigalsub Jaco Mechanism
Long lever mechanism, suitable for heavy loads, the length of the lever makes the trigger very easy to operate. Its main feature is the fixing without traditional side pins, it is mounted on the speargun by means of three screws, its support points are all flat, the contact points between the tooth and the trigger are ground to create less friction.
$us 52,45 $us 65,59
$us 52,45
$us 65,59
Sigalsub Smart Mechanism
Made of burnished stainless steel, this mechanism for wooden spearguns is characterized by an extreme sensitivity of release of the rod with consequent negligible effort of the finger on the trigger. The line release is incorporated in the mechanism and releases the line at the same time as the rod is released; it is possible to mount the line release both on the right and on the left, removing and repositioning a single screw. The contact points between trigger and lever are rectified.
$us 52,45 $us 65,59
$us 52,45
$us 65,59
Sigalsub Easy Mechanism
Long lever mechanism, suitable for heavy loads, the length of the lever makes the trigger very easy to operate. Its main feature is the fixing without traditional side pins, it is mounted on the speargun by means of three screws, its support points are all flat, the contact points between the tooth and trigger are ground to create less friction.
$us 52,45 $us 65,59
$us 54,76
$us 60,84
Ermes Sub Friction Mechanism Back
The standard clutch mechanism of ermes sub model back is suitable for all speargun spearfishing spearguns, it was designed so that it could also be mounted on wooden spearguns, in fact in a normal reverse mechanism, the dimensions of the seat from perform to house it, and the position in which it would be found, coincide precisely in the stem handle coupling, (mortise tenon) inevitably weakening the structure of the joint with the possibility of breakage that would lead to disastrous consequence
$us 54,76 $us 60,84
$us 54,76
$us 60,84
Ermes New Ocean Friction Mechanism
This mechanism now has the possibility of mounting in the internal components, the Roll system, with reduction operation, thanks to its innovative internal components (patent pending), this system allows to have a sensitivity on the trigger unthinkable with traditional mechanisms at very high loads, (maximum triggering effort 0.500 kg on 300 kg traction !!!) with a practically unlimited duration of the rod coupling component. A system that has yet to be discovered and that always puts us one st